駐車場 出入口 車両カウント — デプロイガイド

プリセット

IP Camera + Edge Compute Box

The entrance IP camera sends its picture to a reComputer next to it. The reComputer counts vehicles crossing a line in the picture and sends vehicles inside and free spaces to your MQTT server.

DevicePurpose
reComputer J30 / J40 (Jetson Orin Nano / Orin NX, JetPack 6.2) or reComputer RK3588 / RK3576 SeriesAnalyses the camera picture and counts vehicles in and out
Entrance IP cameraFilms the lane and provides an RTSP stream
MQTT serverReceives crossing records and free spaces

What you'll get:

  • A record for every vehicle that crosses the line (direction, vehicle type)
  • Live vehicles-inside and free-space figures
  • Data ready for a parking management system, a free-space sign or Home Assistant

Requirements: A working camera RTSP address · An MQTT server (an existing one or a Mosquitto install) · Internet access on the device for the first deployment

1

Deploy the vehicle counting app

Install the counting app on the reComputer and enter the camera and the MQTT server. You draw the counting line in Step 2.

前提条件
  1. You have opened the camera's RTSP address in VLC on a computer and can see the entrance.
  2. You know the MQTT server's IP address and port (usually 1883), and its user name and password (not needed if it accepts anonymous connections).
  3. The reComputer is powered on, connected to the LAN, and can reach the internet to download the app and model.
  4. Jetson: a reComputer J30 / J40 (Jetson Orin Nano / Orin NX) running JetPack 6.2. Any other module or system version stops at the first deployment check.
  5. At least 1 GB of free disk space on the device.
配線
  1. Connect the reComputer and the camera to the same LAN with Ethernet cables (if the camera is powered by a PoE switch, plug the reComputer into the same switch).
  2. Mount the camera so it looks at the lane, with vehicles moving from one side of the picture to the other and each vehicle fully in view.
  3. Enter the camera address, MQTT server, site ID, entrance ID and total spaces, then click Deploy.
トラブルシューティング
IssueSolution
UNSUPPORTED_JETSON_MODULE or UNSUPPORTED_JETPACKThis solution supports only reComputer J30 / J40 (Jetson Orin Nano / Orin NX) with JetPack 6.2; use one of those or reflash the system
MISSING_BOARD_LIBRARIES (RK3588 / RK3576)The message lists what is missing; install the RKNN runtime, MPP/RGA, gstreamer1.0-rockchip and gstreamer1.0-plugins-bad following the board vendor's instructions, then deploy again
Model or app download failsMake sure the device can reach the internet, then deploy again; parts already downloaded are reused
Not enough disk spaceRemove unused files or images on the device so that at least 1 GB is free
The counting service does not start, or waiting for it times outRun docker logs edge-parking-counting-jetson on the device (edge-parking-counting-rk3588 on RK3588, edge-parking-counting-rk3576 on RK3576) to see the error
The log shows Address already in useAnother program on the device uses the port: for 8080, change "Counter service port"; for 8099, change "Status port" on Jetson, or stop the program using 8099 on RK3588 / RK3576. Then deploy again
An ID is rejectedSite ID and entrance ID may only contain letters, digits, - and _
デプロイ後

The last deploy step waits until the counting service is ready, so a successful deploy means it is running. Next, draw the counting line in Step 2.

デプロイ方法

Deploy over SSH from this computer to a reComputer J30 / J40 (Jetson Orin Nano / Orin NX, JetPack 6.2) on the LAN.

入力が必要な項目（SenseCraft Solution アプリで入力）
  • Camera stream URL*

    RTSP address of the entrance camera. Open it in VLC first; a wrong path, user name or password is the most common failure.

  • MQTT server address*

    IP address or host name of the MQTT server that receives the counts. It must be reachable from this device.

  • MQTT port*既定値 1883
  • MQTT user name

    Leave empty if the server accepts anonymous connections.

  • MQTT password
  • Site ID*既定値 demo-lot

    First part of every MQTT topic; use one value per car park. Letters, digits, - and _ only, up to 16 characters.

  • Entrance ID*既定値 gate-a

    Names this entrance in topics and events. Letters, digits, - and _ only, up to 15 characters.

  • Total spaces*既定値 120

    Used to report free spaces. Enter 0 if you only need in/out counts.

  • Counter service port*既定値 8080

    Local port the counting service listens on. Change it only if another program on this device already uses 8080.

  • Status port*既定値 8099

    Port for the service status check. Change it only if another program on this device already uses 8099, and enter the same value in the check step.

2

Draw the counting line

Open the counting line page, draw the line across the lane, check the in/out sides and enter the vehicles already inside.

配線
  1. The device IP and counter service port are carried over from Step 1 (127.0.0.1 for a deployment on this device). Open the page; it shows the live camera picture.
  2. Press and drag on the picture to draw a line across the whole lane; drag the dot at either end to fine-tune it. Put the line where vehicles drive through steadily and are fully visible, away from where they queue for the barrier.
  3. Check the "进 IN" and "出 OUT" labels on either side of the line: IN must be the side a vehicle is on after it has entered the car park. If they are reversed, click "Swap in/out".
  4. Click "Save". The line applies immediately and is kept across restarts and redeployments.
  5. Under "Vehicles inside now", enter the number of vehicles parked inside right now and click "Set".
トラブルシューティング
IssueSolution
Page does not openCheck that the IP is the counting device's address, the port matches "Counter service port" in Step 1, and this computer is on the same network
Page opens but shows no pictureThe device cannot reach the camera: open the RTSP address in VLC on the same network and check the path, user name and password; on RK3588 / RK3576 also check that "Camera video format" matches the camera setting. Then deploy again
A vehicle crosses but the counts do not changeMove the line to where vehicles are fully visible and drive through steadily, then click "Save"; the line must cross the whole lane. On RK3588, make sure vehicles stay in view for about 1 second or longer
Entries and exits are swappedClick "Swap in/out", then "Save"
"Line too short"The drag was too short; drag a longer line on the picture
"Save failed" after clicking SaveReload the page and draw the line again; if it still fails, run docker logs edge-parking-counting-jetson on the device (edge-parking-counting-rk3588 on RK3588, edge-parking-counting-rk3576 on RK3576) to see the error
No MQTT messages arriveCheck the MQTT server address, port, user name and password, and that the device can reach port 1883 on the server, then deploy again
デプロイ後

The counting line is active. When a vehicle crosses it, a crossing record and the car park status are sent to your MQTT server.

Initial Setup

  1. If the count of vehicles inside no longer matches the car park, enter the correct number under "Vehicles inside now" on this page at any time and click "Set".
  2. "Total spaces" is used to work out free spaces and is entered in Step 1. To change it, enter the new value in Step 1 and deploy again; the saved counting line is kept.

Quick Verification

  1. Keep the page open and drive a vehicle in. It is boxed, and after it crosses the line "In" goes up by 1, "Inside" up by 1 and "Free" down by 1.

  2. Drive it out. "Out" goes up by 1 and "Inside" down by 1.

  3. If entering vehicles are counted as leaving, click "Swap in/out", then "Save".

  4. On a computer that can reach the MQTT server, subscribe to the counting topics (replace demo-lot with your site ID). Within a few seconds of a crossing you receive a .../crossing message (direction in or out) and a .../occupancy message:

    mosquitto_sub -h <MQTT server IP> -p 1883 -t 'demo-lot/parking/#' -v